-- NAS EXPLORER -- _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** QSI BOARD: NAS-PLUG LE U-Boot 1.1.4 (Jun 10 2010 - 08:28:13) Marvell version: 3.4.27 QSI NAS version: 1.0.4 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 NAS>> usb start;ext2load usb 0:1 $(loadaddr) /boot/uImage;set bootargs console=ttyS0,115200 root=UUID=93f87267-e952-437c-a87a-76712671784f rootwait;bootm $(loadaddr) (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found . ......................... ......................... ......................... ......................... ......................... ......................... ......................... ......................... ......................... ......................... ......................... ......................... ....................... .. ......................... ......................... ......................... ......................... ......................... ........ ................ ......................... ......................... ......................... ......................... ......................... ................ ......... ......................... . ....................... 7079830 bytes read ## Booting image at 02000000 ... Image Name: Linux 2.6.32-5-kirkwood GoFlex Created: 2011-04-25 1:26:55 UTC Image Type: ARM Linux Multi-File Image (uncompressed) Data Size: 7079766 Bytes = 6.8 MB Load Address: 00008000 Entry Point: 00008000 Contents: Image 0: 1401636 Bytes = 1.3 MB Image 1: 5678118 Bytes = 5.4 MB Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-5-kirkwood (unknown) (mute@atom) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu4) ) #4 Sun Apr 24 20:56:34 EDT 2011 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate GoFlex Net [ 0.000000] Ignoring unrecognised tag 0x41000403 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=UUID=93f87267-e952-437c-a87a-76712671784f rootwait [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120032KB available (3376K code, 578K data, 112K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000000] Console: colour dummy device 80x30 [ 0.000132] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776) [ 0.240088] Security Framework initialized [ 0.240107] SELinux: Disabled at boot. [ 0.240135] Mount-cache hash table entries: 512 [ 0.240434] Initializing cgroup subsys ns [ 0.240450] Initializing cgroup subsys cpuacct [ 0.240461] Initializing cgroup subsys devices [ 0.240471] Initializing cgroup subsys freezer [ 0.240479] Initializing cgroup subsys net_cls [ 0.240538] CPU: Testing write buffer coherency: ok [ 0.241302] devtmpfs: initialized [ 0.243033] regulator: core version 0.5 [ 0.243252] NET: Registered protocol family 16 [ 0.243751] Kirkwood: MV88F6281-A1, TCLK=200000000. [ 0.243765] Feroceon L2: Enabling L2 [ 0.243798] Feroceon L2: Cache support initialised. [ 0.245664] bio: create slab at 0 [ 0.245930] vgaarb: loaded [ 0.246385] Switching to clocksource orion_clocksource [ 0.250225] NET: Registered protocol family 2 [ 0.250487] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.251314] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.251414] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.251473] TCP: Hash tables configured (established 4096 bind 4096) [ 0.251482] TCP reno registered [ 0.251644] NET: Registered protocol family 1 [ 0.251817] Unpacking initramfs... [ 0.619802] Freeing initrd memory: 5544K [ 0.619901] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.620162] audit: initializing netlink socket (disabled) [ 0.620197] type=2000 audit(0.610:1): initialized [ 0.626627] VFS: Disk quotas dquot_6.5.2 [ 0.626898] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.626989] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.627633] msgmni has been set to 245 [ 0.629360] alg: No test for stdrng (krng) [ 0.629484] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.629497] io scheduler noop registered [ 0.629505] io scheduler anticipatory registered [ 0.629512] io scheduler deadline registered [ 0.629688] io scheduler cfq registered (default) [ 0.635537] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.636004] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.961639] console [ttyS0] enabled [ 0.965714] NAND device: Manufacturer ID: 0x98, Chip ID: 0xda (Toshiba NAND 256MiB 3,3V 8-bit) [ 0.974414] Scanning device for bad blocks [ 1.038309] Creating 4 MTD partitions on "orion_nand": [ 1.043482] 0x000000000000-0x000000100000 : "u-boot" [ 1.049043] 0x000000100000-0x000000500000 : "uImage" [ 1.054482] 0x000000500000-0x000002500000 : "rootfs" [ 1.059986] 0x000002500000-0x000010000000 : "data" [ 1.065974] mice: PS/2 mouse device common for all mice [ 1.071473] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0 [ 1.077409] i2c /dev entries driver [ 1.081092] cpuidle: using governor ladder [ 1.085319] cpuidle: using governor menu [ 1.089369] Registered led device: goflex:green:health [ 1.094583] Registered led device: goflex:orange:misc [ 1.099719] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver [ 1.106130] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver [ 1.146448] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 1.186445] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) [ 1.226445] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) [ 1.266445] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) [ 1.273225] TCP cubic registered [ 1.276489] NET: Registered protocol family 17 [ 1.281269] registered taskstats version 1 [ 1.286047] rtc-mv rtc-mv: setting system clock to 2011-04-25 01:40:46 UTC (1303695646) [ 1.294110] Initalizing network drop monitor service [ 1.299165] Freeing init memory: 112K Loading, please wait... [ 1.376842] udev[44]: starting version 164 [ 1.667544] SCSI subsystem initialized [ 1.723766] usbcore: registered new interface driver usbfs [ 1.729971] usbcore: registered new interface driver hub [ 1.815470] MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.821358] usbcore: registered new device driver usb [ 1.827312] mv643xx_eth smi: probed [ 1.851596] net eth0: port 0 with MAC address 00:10:75:2a:82:c1 [ 1.874781] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.882852] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 1.888198] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 1.916463] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 1.936432] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 1.942434] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.949272] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.956535] usb usb1: Product: Marvell Orion EHCI [ 1.961260] usb usb1: Manufacturer: Linux 2.6.32-5-kirkwood ehci_hcd [ 1.967652] usb usb1: SerialNumber: orion-ehci.0 [ 1.972802] usb usb1: configuration #1 chosen from 1 choice [ 1.979133] hub 1-0:1.0: USB hub found [ 1.982934] hub 1-0:1.0: 1 port detected [ 1.987093] sata_mv sata_mv.0: version 1.28 [ 1.991421] sata_mv sata_mv.0: slots 32 ports 2 [ 2.009349] scsi0 : sata_mv [ 2.012815] scsi1 : sata_mv [ 2.016061] ata1: SATA max UDMA/133 irq 21 [ 2.020242] ata2: SATA max UDMA/133 irq 21 [ 2.306438] usb 1-1: new high speed USB device using orion-ehci and address 2 [ 2.461106] usb 1-1: New USB device found, idVendor=0ea0, idProduct=2168 [ 2.467855] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.475025] usb 1-1: Product: Flash Disk [ 2.479504] usb 1-1: Manufacturer: USB [ 2.485306] usb 1-1: configuration #1 chosen from 1 choice [ 2.523752] Initializing USB Mass Storage driver... [ 2.528746] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 2.535909] scsi2 : SCSI emulation for USB Mass Storage devices [ 2.542707] usbcore: registered new interface driver usb-storage [ 2.549399] USB Mass Storage support registered. [ 2.556477] ata1.00: ATA-8: ST2000DL003-9VT166, CC98, max UDMA/133 [ 2.562689] ata1.00: 3907029168 sectors, multi 0: LBA48 [ 2.626512] ata1.00: configured for UDMA/133 [ 2.631087] scsi 0:0:0:0: Direct-Access ATA ST2000DL003-9VT1 CC98 PQ: 0 ANSI: 5 [ 2.986430] ata2: SATA link down (SStatus 0 SControl F300) [ 3.021600] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 3.029427] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 3.035617] sd 0:0:0:0: [sda] Write Protect is off [ 3.040563] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.050661] sda: sda1 [ 3.074654] sd 0:0:0:0: [sda] Attached SCSI disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... Begin: Mounting devpts ... mount: mounting none on /dev/pts failed: Device or resource busy done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Waiting for root file system ... [ 7.548315] scsi 2:0:0:0: Direct-Access USB Flash Disk 2.00 PQ: 0 ANSI: 2 [ 7.560902] sd 2:0:0:0: [sdb] 1024000 512-byte logical blocks: (524 MB/500 MiB) [ 7.578265] sd 2:0:0:0: [sdb] Write Protect is off [ 7.583092] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 7.593495] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 7.599650] sdb: sdb1 [ 7.607517] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 7.613645] sd 2:0:0:0: [sdb] Attached SCSI removable disk done. Begin: Running /scripts/local-premount ... done. Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting Using makefile-style concurrent boot in runlevel S. Starting the hotplug events dispatcher: udevd[ 8.653763] udev[214]: starting version 164 . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Activating swap...done. Checking root file system...fsck from util-linux-ng 2.17.2 /dev/sdb1: clean, 14053/128016 files, 379442/510976 blocks done. Loading kernel modules...done. Cleaning up ifupdown.... Setting up networking.... Activating lvm and md swap...done. Checking file systems...fsck from util-linux-ng 2.17.2 done. Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Setting kernel variables ...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:10:75:2a:82:c1 Sending on LPF/eth0/00:10:75:2a:82:c1 Sending on Socket/fallback [ 12.202136] eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting enhanced syslogd: rsyslogd. Starting periodic command scheduler: cron. Starting Dropbear SSH server: [ 75.684721] NET: Registered protocol family 10 dropbear. Debian GNU/Linux 6.0 goflex ttyS0 goflex login: