User Tools

Site Tools


goflex:uartboot
mute@atom:~/goflex$ ./picocom -b 115200 /dev/ttyUSB0
picocom v1.6

port is        : /dev/ttyUSB0
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv
imap is        : 
omap is        : 
emap is        : crcrlf,delbs,

Terminal ready

*** file to upload: uboot.orig
Sending DEBUG for about 5 seconds. Power on device NOW!
Waiting NAK... Press 'x' to escape.
sx -vv -b uboot.orig 
Sending uboot.orig, 4096 blocks: Give your local XMODEM receive command now.
Xmodem sectors/kbytes sent:   0/ 0kRetry 0: Got 0d for sector ACK
Retry 0: NAK on sector
Retry 0: Got 46 for sector ACK
Retry 0: NAK on sector
Retry 0: Got 50 for sector ACK
Retry 0: NAK on sector
Retry 0: Got 6c for sector ACK
Retry 0: NAK on sector
Retry 0: Got 6c for sector ACK
Retry 0: NAK on sector
Retry 0: Got 41 for sector ACK
Retry 0: NAK on sector
Retry 0: Got 44 for sector ACK
Retry 0: NAK on sector
Retry 0: Got 53 for sector ACK
Retry 0: NAK on sector
Retry 0: Got 50 for sector ACK

^Csx: caught signal 2; exiting

*** exit status: 128
done.

*** file to upload: uboot.uart
Sending DEBUG for about 5 seconds. Power on device NOW!
Waiting NAK... Press 'x' to escape.
sx -vv -b uboot.uart 
Sending uboot.uart, 4096 blocks: Give your local XMODEM receive command now.
Xmodem sectors/kbytes sent: 4096/512k
Bytes Sent: 524416   BPS:6280

Transfer complete

*** exit status: 0
done.


U-Boot 1.1.4  Cloud Engines 1.1.2 (3.4.22) SATA PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00691750

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM CS[1] base 0x10000000   size 256MB 
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD (GUESSED): DISCOVERY:0.1

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Unknown command 'usb' - try 'help'
Unknown command 'fatload' - try 'help'

Reset IDE: 
Marvell Serial ATA Adapter
Integrated Sata device found

Unknown command 'fatload' - try 'help'

NAND read: device 0 offset 0x100000, size 0x300000

Reading data from 0x3ff800 -- 100% complete.
 3145728 bytes read: OK
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2010-10-27  19:41:11 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2095528 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...
goflex/uartboot.txt · Last modified: 2023/11/04 22:30 by 127.0.0.1

Except where otherwise noted, content on this wiki is licensed under the following license: Public Domain
Public Domain Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki