Differences

This shows you the differences between two versions of the page.

--- wrtu54g-tm:bootlog26 [2010/06/02 14:53] – created neutronscott
+++ wrtu54g-tm:bootlog26 [2011/04/07 00:54] (current) – removed neutronscott
@@ Line 1: / Line 1: @@
-<code>
-f?4
-(v1.00.02) U-Boot 2.1.4 (Jan 28 2008 - 14:56:42)
-DRAM:  64 MB
-Flash:  8 MB
-In:    serial
-Out:   serial
-Err:   serial
-Net:   adm8668_net
-Hit any key to stop autoboot:  0
-ADM8668 # set bootfile vmlinuz-2.6
-ADM8668 # run tftp_boot
-TX error status2 = 0x04000008
-Using adm8668_net device
-TFTP from server 10.42.43.1; our IP address is 10.42.43.8
-Filename 'vmlinuz-2.6'.
-Load address: 0x600000
-Loading: T T ###################################T ############################################################################T ##################
-	 ############T ################################################T ##########################################################T ############
-	 ##################################################################################################################################
-	 ##################################################################################################################################
-	 ##################################################################################################################################
-	 ################################
-done
-Bytes transferred = 1741413 (1a9265 hex)
-## Booting image at 80600000 ...
-Check vendor string...    Image Name:   ADM8668 Linux Kernel(2.4.31)
-   Created:      2010-05-27  15:50:22 UTC
-   Image Type:   MIPS Linux Kernel Image (gzip compressed)
-   Data Size:    1741349 Bytes =  1.7 MB
-   Load Address: 00002000
-   Entry Point:  80006280
-   Verifying Checksum ... OK
-   Uncompressing Kernel Image ... OK
-Starting kernel ...
-[    0.000000] bootconsole [ttyS0] enabled
-[    0.000000] CPU revision is: 0001800b (MIPS 4Kc)
-[    0.000000] Determined physical RAM map:
-[    0.000000]  memory: 03ffffff @ 00000000 (usable)
-[    0.000000] Zone PFN ranges:
-[    0.000000]   Normal   0x00000000 -> 0x00003fff
-[    0.000000] Movable zone start PFN for each node
-[    0.000000] early_node_map[1] active PFN ranges
-[    0.000000]     0: 0x00000000 -> 0x00003fff
-[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16255
-[    0.000000] Kernel command line: root=/dev/nfs rw nfsroot=10.42.43.1:/nfs/busybox,v3 ip=dhcp
-[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
-[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
-[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
-[    0.000000] Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
-[    0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
-[    0.000000] Memory: 60736k/65532k available (3174k kernel code, 4720k reserved, 627k data, 152k init, 0k highmem)
-[    0.000000] NR_IRQS:32
-[    0.000000] ADM8668 CPU clock: 200 MHz
-[    0.000000] MIPS timer IRQ: 23
-[    0.000000] 63xx_console_init();
-[    0.000000] Calibrating delay loop... 198.65 BogoMIPS (lpj=397312)
-[    0.092000] Mount-cache hash table entries: 512
-[    0.108000] NET: Registered protocol family 16
-[    0.120000] adm8668_pci_init()
-[    0.120000] ADM8668 DEV: register uart
-[    0.124000] ADM8668 DEV: register usbh
-[    0.276000] bio: create slab <bio-0> at 0
-[    0.288000] usbcore: registered new interface driver usbfs
-[    0.292000] usbcore: registered new interface driver hub
-[    0.296000] usbcore: registered new device driver usb
-[    0.304000] Advanced Linux Sound Architecture Driver Version 1.0.21.
-[    0.308000] =======adm8668netfixup======
-[    0.316000] pci 0000:00:01.0: BAR 0: assigned [mem 0x16000000-0x16007fff]
-[    0.320000] pci 0000:00:01.0: BAR 0: set to [mem 0x16000000-0x16007fff] (PCI address [0x16000000-0x16007fff]
-[    0.324000] pcibios_fixup_irqs (slot:1 devfn:8 oldirq:0)
-[    0.336000] cfg80211: Calling CRDA to update world regulatory domain
-[    0.340000] Switching to clocksource MIPS
-[    0.368000] NET: Registered protocol family 2
-[    0.372000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
-[    0.380000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
-[    0.384000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
-[    0.392000] TCP: Hash tables configured (established 2048 bind 2048)
-[    0.396000] TCP reno registered
-[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
-[    0.404000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
-[    0.412000] NET: Registered protocol family 1
-[    0.420000] RPC: Registered udp transport module.
-[    0.420000] RPC: Registered tcp transport module.
-[    0.428000] RPC: Registered tcp NFSv4.1 backchannel transport module.
-[    0.436000] adm8668_uart.0: ttyS0 at MMIO 0x1e400000 (irq = 6) is a adm8668_uart
-[    0.440000] console [ttyS0] enabled, bootconsole disabled
-[    0.440000] console [ttyS0] enabled, bootconsole disabled
-[    0.468000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
-[    0.476000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
-[    0.484000] msgmni has been set to 118
-[    0.492000] alg: No test for stdrng (krng)
-[    1.000000] io scheduler noop registered (default)
-[    1.068000] loop: module loaded
-[    1.076000] ADM8668 NOR flash device: 800000 at 10000000
-[    1.080000] adm8668: Found 1 x16 devices at 0x0 in 16-bit bank
-[    1.084000]  Amd/Fujitsu Extended Query Table at 0x0040
-[    1.092000] number of CFI chips: 1
-[    1.092000] Creating 4 MTD partitions on "adm8668":
-[    1.100000] 0x000000040000-0x000000110000 : "vmlinuz"
-[    1.116000] 0x000000110000-0x000000600000 : "rootfs"
-[    1.128000] 0x000000600000-0x000000800000 : "user"
-[    1.144000] 0x000000040000-0x000000600000 : "firmware"
-[    1.160000] ADM8668 NOR flash device initialized
-[    1.164000] PPP generic driver version 2.4.2
-[    1.172000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
-[    1.176000] ------------------------------------------
-[    1.180000] PCI dev init 8
-[    1.208000] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
-[    1.212000] ------------------------------------------
-[    1.220000] PCI dev init 0
-[    1.220000] tulip0:  MII transceiver #1 config 3100 status 7869 advertising 05e1.
-[    1.236000] eth0: ADMtek Comet rev 0 at Port 0x11600000, 00:21:29:ef:53:f5, IRQ 8.
-[    1.244000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
-[    1.252000] Initalizing ADM8668 USB
-[    1.252000] ADM8668 version: 86880002
-[    1.256000] adm8668_ehci adm8668_ehci: ADM8668 EHCI
-[    1.260000] adm8668_ehci adm8668_ehci: new USB bus registered, assigned bus number 1
-[    1.272000] adm8668_ehci adm8668_ehci: irq 15, io mem 0x11200000
-[    1.288000] adm8668_ehci adm8668_ehci: USB 0.0 started, EHCI 0.33
-[    1.292000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
-[    1.296000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
-[    1.304000] usb usb1: Product: ADM8668 EHCI
-[    1.308000] usb usb1: Manufacturer: Linux 2.6.33.2 ehci_hcd
-[    1.316000] usb usb1: SerialNumber: ADM8668
-[    1.324000] hub 1-0:1.0: USB hub found
-[    1.328000] hub 1-0:1.0: 5 ports detected
-[    1.348000] usbcore: registered new interface driver cdc_acm
-[    1.352000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
-[    1.368000] usbcore: registered new interface driver snd-usb-audio
-[    1.372000] ALSA device list:
-[    1.376000]   No soundcards found.
-[    1.380000] Netfilter messages via NETLINK v0.30.
-[    1.384000] nf_conntrack version 0.5.0 (950 buckets, 3800 max)
-[    1.392000] ctnetlink v0.93: registering with nfnetlink.
-[    1.396000] ip_tables: (C) 2000-2006 Netfilter Core Team
-[    1.400000] TCP cubic registered
-[    1.404000] NET: Registered protocol family 17
-[    1.924000] rt61pci 0000:00:01.0: firmware: using built-in firmware rt2561s.bin
-[    2.984000] Sending DHCP requests ., OK
-[    3.492000] IP-Config: Got DHCP answer from 10.42.43.1, my address is 10.42.43.10
-[    3.504000] IP-Config: Complete:
-[    3.508000]      device=eth0, addr=10.42.43.10, mask=255.255.255.0, gw=10.42.43.1,
-[    3.516000]      host=10.42.43.10, domain=, nis-domain=(none),
-[    3.520000]      bootserver=10.42.43.1, rootserver=10.42.43.1, rootpath=
-[    3.528000] prepare_namespace()
-[    3.532000] ROOT=0:ff [is not ramdisk]
-[    3.532000] Looking up port of RPC 100003/3 on 10.42.43.1
-[    3.544000] Looking up port of RPC 100005/3 on 10.42.43.1
-[    3.576000] VFS: Mounted root (nfs filesystem) on device 0:11.
-[    3.580000] Freeing 0 UNUSED PROM BISH
-[    3.584000] Freeing unused kernel memory: 152k freed
-[    3.608000] run_init_process(/sbin/init)
-[    4.312000] Algorithmics/MIPS FPU Emulator v1.5
-mount: mounting /dev/mtdblock2 on /jffs failed: No such file or directory
-[    4.980000] eth0: Setting full-duplex based on MII#1 link partner capability of 41e1.
-jffs2: making jffs2 partition on mtd2...
-Erasing 64 Kibyte @ 200000 - 100% complete.
-Configuration file: /etc/hostapd.conf
-[   23.452000] cfg80211: Calling CRDA for country: JP
-Using interface wlan0 with hwaddr 00:21:29:ef:53:f3 and ssid 'wrtu54g-tm'
-Starting httpd: OK
-Starting dnsmasq: OK
-Starting dropbear sshd: generating dsa key... OK
-[   27.120000] JFFS2 notice: (190) read_dnode: node CRC failed on dnode at 0x000690: read 0x680fe38f, calculated 0x41dba4de
-[   27.136000] JFFS2 warning: (190) jffs2_do_read_inode_internal: no data nodes found for ino #9
-[   27.148000] iget() failed for ino #9
-neutronscott wrtu54g-tm (v0.1) super alpha beta
-wrtu54g-tm login: root
-Password:
-# ps
-  PID USER       VSZ STAT COMMAND
-root      1160 S    init
-root         0 SW   [kthreadd]
-root         0 SW   [ksoftirqd/0]
-root         0 SW   [events/0]
-root         0 SW   [khelper]
-root         0 SW   [async/mgr]
-root         0 SW   [sync_supers]
-root         0 SW   [bdi-default]
-root         0 SW   [kblockd/0]
-root         0 SW   [khubd]
-root         0 SW   [kseriod]
-root         0 SW   [cfg80211]
-root         0 SW   [rpciod/0]
-root         0 SW   [kswapd0]
-root         0 SW   [aio/0]
-root         0 SW   [nfsiod]
-root         0 SW   [crypto/0]
-root         0 SW   [mtdblockd]
-root         0 SW   [phy0]
-root         0 SWN  [jffs2_gcd_mtd2]
-root      1572 S    hostapd -P /tmp/hostapd.conf -B /etc/hostapd.conf
-root      1152 S    httpd -c /etc/httpd.conf -h /var/www
-nobody    1016 S    /usr/sbin/dnsmasq
-root      1296 S    /usr/sbin/dropbear -d /tmp/dropbear_dss_host_key
-root      1188 S    -sh
-root      1148 S    /sbin/syslogd -n
-root      1144 S    /sbin/klogd -n
-root      1152 R    ps
-# cat /proc/cpuinfo
-system type		: IFXADM8668
-processor		: 0
-cpu model		: MIPS 4Kc V0.11
-BogoMIPS		: 198.65
-wait instruction	: yes
-microsecond timers	: yes
-tlb_entries		: 16
-extra interrupt vector	: yes
-hardware watchpoint	: yes, count: 1, address/irw mask: [0x0fff]
-ASEs implemented	:
-shadow register sets	: 1
-core			: 0
-VCED exceptions		: not available
-VCEI exceptions		: not available
-#
-</code>